It looks like you're in USA.
Do you want to navigate to
our USA site?
Important cautions
To put the ECU into for advanced flashing or recovery, hardware modifications are required within the unit: me7.4.5 pinout
| Pin | Connector | Signal Name | Description | Typical Function | |------|-----------|----------------|--------------------------------|--------------------------| | 1 | A | Ground | Sensor ground | - | | 2 | A | EVAP Canister Purge Valve (N80) | Duty cycle control | Emissions | | 3 | A | Ground | Power ground for injectors/coils | - | | 4 | A | +12V Battery | Permanent power (Terminal 30) | ECU memory | | 5 | A | +12V Switched (Terminal 15) | Switched via ignition | Wake-up signal | | 6 | A | CAN-High | Drivetrain CAN bus | ABS, Instrument cluster | | 7 | A | CAN-Low | Drivetrain CAN bus | ABS, Instrument cluster | | 8 | A | Brake light switch signal | Input | Brake pedal | | 9 | A | Clutch pedal switch | Input | Cruise control / starting | | 10 | A | A/C compressor request | Input | Climate control | | 11 | A | Radiator fan activation (low speed) | Output | Cooling | | 12 | A | Radiator fan activation (high speed) | Output | Cooling | | 13 | A | --- | Not used | - | | 14 | A | Alternator excitation signal | Output | Charge warning | | 15 | A | Diagnostic K-Line (ISO 9141) | Bi-directional | OBD2 communication | | 16 | A | --- | Not used | - | | 17 | A | --- | Not used | - | | 18 | A | --- | Not used | - | | 19 | A | Fuel pump relay control | Output | Activates FP relay | | 20 | A | Engine speed output (RPM signal) | Output | Tachometer cluster | | 21 | A | MIL (Check engine light) | Output | Warning lamp | | 22 | A | EPC light | Output | Electronic Power Control | | 23 | A | +5V Sensor supply | Reference voltage | For MAP, TPS, etc. | | 24 | A | --- | Not used | - | | 25 | A | --- | Not used | - | | 26 | A | --- | Not used | - | | 27 | A | --- | Not used | - | | 28 | B | Knock sensor 1 (cyl 1 & 2) | Signal input | Ignition timing control | | 29 | B | Knock sensor 2 (cyl 3 & 4) | Signal input | Ignition timing control | | 30 | B | Sensor ground (shield) | For knock sensors | - | | 31 | B | Intake Air Temp (IAT) | Signal input | Inside MAF or TMAP | | 32 | B | Engine Coolant Temp (ECT) | Signal input | Temperature compensation | | 33 | B | Shield ground | For crank/cam sensors | - | | 34 | B | MAF signal | Frequency/duty cycle | Airflow metering | | 35 | B | MAF ground | Sensor return | - | | 36 | B | G28 Engine speed (crank sensor) | Differential signal (-) | RPM base timing | | 37 | B | G28 Engine speed (crank sensor) | Differential signal (+) | RPM base timing | | 38 | B | G40 Camshaft position sensor | Hall effect signal | Sequential injection | | 39 | B | Throttle position sensor (G187) | Signal 1 (closing) | ETC | | 40 | B | Throttle position sensor (G188) | Signal 2 (opening) | ETC redundancy | | 41 | B | Accelerator pedal position (G79) | Signal 1 | Driver demand | | 42 | B | Accelerator pedal position (G185) | Signal 2 | Redundant signal | | 43 | B | MAP sensor (Integrated) | Boost pressure signal | Inside ECU case | | 44 | B | MAP sensor ground | Internal ECU | - | | 45 | B | External MAP (for some models) | Boost input (rare) | - | | 46 | B | --- | Not used | - | | 47 | C | Injector cylinder 1 | Output (ground switch) | Fuel delivery | | 48 | C | Injector cylinder 2 | Output (ground switch) | Fuel delivery | | 49 | C | Injector cylinder 3 | Output (ground switch) | Fuel delivery | | 50 | C | Injector cylinder 4 | Output (ground switch) | Fuel delivery | | 51 | C | Ignition coil 1 (power stage) | Output | Spark | | 52 | C | Ignition coil 2 (power stage) | Output | Spark | | 53 | C | Ignition coil 3 (power stage) | Output | Spark | | 54 | C | Ignition coil 4 (power stage) | Output | Spark | | 55 | C | N75 Boost control valve | PWM output | Wastegate control | | 56 | C | Idle Air Control (N71) | PWM output (if not DBW) | Idle stabilization | | 57 | C | Secondary air injection pump relay | Output | Cold start emissions | | 58 | C | Secondary air injection valve (N112) | Output | Air diverter | | 59 | C | O2 sensor heater (Bank 1, Sensor 1) | Output | Lambda heating | | 60 | C | O2 sensor heater (Bank 1, Sensor 2) | Output (post-cat) | Heating | | 61 | C | O2 sensor (Sensor 1) signal | Input (0-1V or wideband) | AFR | | 62 | C | O2 sensor (Sensor 1) ground | Ground for lambda | - | | 63 | C | O2 sensor (Sensor 2) signal | Input | Post-cat monitoring | | 64 | C | O2 sensor (Sensor 2) ground | Ground | - | | 65 | C | Fuel tank pressure sensor | Input | Leak detection | | 66 | C | --- | Not used | - | | 67 | C | --- | Not used | - | | 68 | C | --- | Not used | - | | 69 | A | +12V Switched (Terminal 15) duplicate | Redundant | Safety | | 70 | A | Ground | Power ground | High current | | 71 | A | Ground | Power ground | High current | | 72 | A | +12V Battery duplicate | Redundant main power | - | | 73 | A | +12V Battery duplicate | Redundant main power | - | | 74-121 | --- | Various unused or vehicle-specific pins | (e.g., cruise control, A/C pressure) | Check wiring diagram | Important cautions To put the ECU into for
The ME7.4.5 ECU is a sophisticated engine control unit designed by Bosch for gasoline and diesel engines. It features advanced technologies, such as fuel injection, ignition timing, and emissions control. The ECU processes data from various sensors to optimize engine performance, efficiency, and reliability. The ECU processes data from various sensors to